Holy sht. I know what im doing this weekend.

I played the crap out of blue prince and I actually hated the game. Might just be me though but IMO the game has some incredible big flaws.

I completed an absurd amount of the game in spite just so I was 100% sure I hated it. Imo one of the most overrated games I’ve played.

I think if you consider is as a percentage of all homes, the number doesnt look as insane. There’s about 133m homes and 17m are vacant according to the article which is roughly 13% of homes are empty.

I’m not sure what the average vacancy rate is in other countries is so not sure how bad 13% is but it doesnt sound as crazy as 27x.

Update: According to this article the US does rank pretty high in vacant properties. Im actually surprised Japan is 1st.

https://realestatemagazine.ca/canada-ranks-11th-for-the-highest-proportion-of-empty-homes/

Thats actually what I guessed was happening. Sometimes I make accounts on services I don’t use just to “reserve” the username.

😬

Just suppress the warning /s

Yeah i sprinkle they shit in everything i cook

Like… Neutered or… /s

True. I’ll try to do all of the belt tension troubleshooting on their website first and if it doesnt work I’ll reach out.

So it is kind of bad I assume. Prusa recommends 96hz for the top belt and 92 hz for the bottom belt but i cant hit those numbers. For some reason my bottom belt is tighter than the top one. If I try to tighten the top belt more than the bottom one my gantry is no longer square. I think something is messed up so I’m going to just take the belt assembly apart and see if I can figure it out :/

Oof that sounds rough. I hope it’s all fine now.

Wow, I was lied to by a meme. /s

I actually googled this a while back and IIRC they can also roll around or just tilt their body as well.

It’s half the reason I got a steam deck. It can’t play everything but it can play a good portion of my games and I can plug it into a TV.

can you just build them a ramp?

I’m not going to say it was smooth sailing but I think I’m through the rough waters. This past day I’ve been printing basically non-stop and every print has been pretty much flawless.

The days before this though I had:

• Diagnose z-axis movement issues.
• Accidentally printed PETG onto the smooth bed plate. (I knew this was bad but I just assumed it was bad adhesion, I didn’t realize the problem was the opposite LOL)
• Broke the belt tension adjustment piece and had to drill holes into it to remove it and replace it with a piece I printed with PETG.
• Diagnose a “ghost clog” where I took off the nozzle, found no clog, took apart the nextruder and found nothing and realized at the end it was bad filament.

I do not have a caliper unfortunately but I do have one arriving in the mail in a week or so. I realized I needed one once I started trying to design things with a tight fit.

Yeah. The good news is after cutting off the problematic part of the spool, the rest of it has been printing very nicely and I’m already halfway done the spool.

I was using Prusa’s default profile for PETG which heats the nozzle up to 250 C. If you are correct about it being PET, it should still have melted.

It was a brand new spool so the extruder idea is probably out. Also I tried cutting 10cm off of it which should be long enough that it would be too far away from the extruder anyways. I was also using Prusa’s default profile which heats the nozzle to 250 C! Anyways I’m glad I figured it out. Next time I suspect a nozzle clog though I’m going to try swapping the filament as well before I do something major like take apart the extruder.

I think the consensus from my research is that PLA sucks for practical prints. If you are going to put a constant load on it or if the location can get a bit hot then the print can fail. PLA is also very rigid which can be good but can also be a negative if you want some give. I’m probably only going to use PLA for more “show pieces” that will only be used indoors and will not take a beating. For things like plastic cases, it’s probably fine.